try map gas it heats up faster and hotter also try a pipe wrench
if you can get the wrench in there had to do it to a suburban
last month

anyone know the gm part number for block heater
I have one gm part number is 1#25537080
just don't want to take freeze plug out and find out it don't fit
thanks

i turn my on and the car shuts off so i dont use it anymore lol

well i checked voltage at knock sensors the one for odd side of block
2.5 volts
even side of block 0 volts
could this be a pcm problem
does this wire go to the coil pack computer
or strait to pcm

just that code so this would cause a miss too
i pull one wire at a time at coil packs has spark put the even side is weaker than
odd side
at idle and maybe up to 2000 rpm misses but clears up above 2000rpm

325 code

ill do that, now i have a esc failure code

well went to change fuel rail and found that the vaccum hose plug that goes into the
intake had poppped out so put it in and runs like it should. this happen when i wanted to see
if just doing the cam sensor would make it run and it popped threw the intake but didnt click in my head
that it could of ...

ill change the regulator/fuel rail have one that was just pulled off a know running 2000 3.8

what about timing chain jumpin a tooth or two

hey guy its been a while
here is my problem on the 95 bonne 3.8l non super charged
the other night it had a miss fire change coil pack for 5 and 2
ran great till next day cranks no run so with it having 230,000
changed cam and crank sensors now it runs but not well
have to keep foot on pedal to make ...

1983 buick regal (still own)
1976 olds cutlass (engine and trans for the regalthen junked it)
1986 mercury linx (winter car lasted 4months that year junked it)
1983 buick regal (parts car)
1984 buick grand national(ended up parting it out)
2000 chevy xtreme (first new car)
1986 pontiac parisienne ...

hope this is in the right forum
i can get a door and fender from crash93ssei
but my trim is se on my car now and he can get me ssei door and fender
my question is i want to put the se trim on the the new parts can do this without
any problems or is this going to be a problem
thanks

you guys are right no one got hurt and thats the main thing
and it does needs fender,door,marker light
tommorow goona hit up some yards.
the gold wheels came off of 93 se bonne i had

i got the marker light and center cap
wife and daughter are ok
she was going 50mph and the deer slamed right into her
she hit the bakes so it wouldnt hit the rear door where
my daughter was sleeping.

http://i301.photobucket.com/albums/nn51/TUFFREGAL/bonnetookadeerhit005.jpg

http://i301 ...

thanks i went to the dealer and talked to the head guy of service at Bill Jacobs of Joliet ,il
what a nice guy told me to about the 10% of the comperssion differance of each one so #6 is to low could be why it pushes oil every 3000 miles
so looks like the engine comes out for rings and bearings ...

on my 02 gmc 6.0L i did a compression check
and #6 cyl was at 145 and the rest were between 170 to 180
should i just put new rings in all 8 or should it be ok already have heads off to fix
broken exhaust manifold bolt
engine has 141,000 on it and looks new inside
any info would help thanks

your right series II
thanks

what s the differance between fwd 3.8l series 1
and the 3.8l rwd in the firebirds and camaros 93 and up
can anything be swapped and if so what can be
thanks

just so you know i just picked up a 95 suburban parts truck
so if you need a computer or a part or two just let me know