They are the ones inquiring about it. They requested I send a factory coil in for the rear. So I will be searching a bone yard unless I can get the specs they requested. cant just remove one from the car you know daily driver.

Ok folks Today I'm in the process of ordering custom springs For Bonnie. My daughter is studying to be a mechanic. Not my son but daughter go figure. So we have argued about the proper way to lower an automobile after the Honda Gen has simply made it look like someone stepped on a hot wheels. Camber ...

I also replaced my ISS due to the same clunking. When I was looking up the old design vs the new and advice from this site, I discovered that the original design was bad conpaired to the updated version of it. replaced it instead of lubing it and am very satisfied with the end resault very ...

I had a misfire on 6 turned out to be an intermittent fuel injector. While in idle it has a slight stumble. However step on it, the stumble was horrible. Felt as if the tranny was falling off.

Agreed its possibly the gas cap. the one on my car is very intermittent the rest of the system is solid. i will replace it before winter hits

When I got that misfire I had to replace my lower intake gasket. there was a very small in the front of the engine. Found it by spraying carb cleaner around all the mated surfaces cars been great since.

I went with ZZP 3 inch down pipe with a new cat and its incredible thank you for your feed back it helped me make a great decision. Chose it stainless steel got delivered quickly so credit goes to zzp great quality part !

The only parts getting replaced is the cat converter and the down pipe everything else is good. but since i am under might as well do something my way !

Time has come to replace the disaster the unnamed national muffler shop did to my poor automobile. So long story short they welded the front pipe to the cat converter and causing this good awful rattle in the cat. Probably done when they hacked the new cat converter.. Still pisses me off any way I'm ...

I have used Timken Also For both front and rear happy with the end result..

Yes sir it was nice to fill it up and get an estimated mileage of 420 miles and chirping the tires leaving the gas station !

I just re did mine went with the felpro and I also picked up the cooling elbows under 5 dollars at Auto Zone, when removing the LIM the old one broke. thankful I did get them. While I was at it I replaced the cooling hoses and the thermostat the felpro kit included everything even the o rings for ...

After taking it apart decided to do the lower intake at the same time. Took my time with it cleaned replaced the gaskets again Thanks to Harofreak for having the parts I needed to complete my project. This time i needed a vacuum t an injector and project complete now is is running like she did when ...

Problem solved it was the hose that came from the back of the Compressor replaced the hose thanks to Harofreak and replaced seals and the filter back to cold just in time for cold weather !!

Best thing to do is usually replacement. Anything rusting its best to just cut it out and replace. The best part of this is that we have members here that have an extensive collection of spare parts. Contact harofreak00 on this group see if he has the parts you need he is awesome

What i am looking for is the process and torque specs for the bolts. I cant locate the info for the process on this type of super charger

Thanks Again guys !!

Most likely its a bad gas pump.. However the check the gas cap is usually the rubber ring not sealing check where it mates with the gas tank check it for rust if so clean it up. replace the gas cap.. Mine used to do that fixed it with what i have suggested.As far as the fuel gage not working its ...

Tested again this morning but with more light and no distractions when spraying the fuel rail the over spray was leaking onto the supercharger which would cause it to stop the stumble. so i sprayed at the base and that sound like i have located my vacuum leak. the gasket needs replacing..parts on ...

That never crossed my mind that is a possibility will do first thing in the morning.

So its a basic old school install what i did was hit or miss till i found one that shut off with the ignition when i get a chance i will go out and tell you which fuse i tied into. I also went at it from under the fuse box with a clip