Shallow aftermarket receiver?
-
IanRosean
- SLE Member

- Posts: 27
- Joined: Wed Feb 12, 2014 10:56 am
- Year and Trim: 2000 Pontiac Bonneville SE
Shallow aftermarket receiver?
Does anyone know of a shallow CD-less media head unit that is like am fm USB Aux and possibly blue tooth, that the depth is like super shallow like around 4 inches deep so I do not have to cut the plastic that is behind the stock radio? Any input is greatly appreciated, I am terrified of attempting to cut that plastic and something going wrong.
- bobgto65
- Posts like an L36

- Posts: 866
- Joined: Thu May 29, 2008 7:52 pm
- Year and Trim: 2002 SSEi
2004 Bonneville GXP - Location: Maryland
Re: Shallow aftermarket receiver?
I have not seen one. But cutting out the back of the dash is not too hard to do. And it will not prevent you from reinstalling the factory radio later on.
bobgto65

2004 Bonneville GXP 62,000 miles purchased 04/13
2009 G8 GXP PBM, M6 9580 miles, no mods, sold 08/15
2009 G8 GT SBM 36,000 miles, modded 430 whp
2002 Bonneville SSEi 203,200 miles (sold 3/2014)

2004 Bonneville GXP 62,000 miles purchased 04/13
2009 G8 GXP PBM, M6 9580 miles, no mods, sold 08/15
2009 G8 GT SBM 36,000 miles, modded 430 whp
2002 Bonneville SSEi 203,200 miles (sold 3/2014)
- burger
- SSE Member

- Posts: 147
- Joined: Fri Oct 28, 2011 11:09 pm
- Year and Trim: 1997 Pontiac Bonneville se
- Location: Maple Grove mn
Re: Shallow aftermarket receiver?
Also you can get an a dash install kit that sticks out like an inch so you dont have to cut anything. At least it is that way for the older models.

97 Bonneville se-Winter car
85 Yamaha xj700-Summer cruiser
-
IanRosean
- SLE Member

- Posts: 27
- Joined: Wed Feb 12, 2014 10:56 am
- Year and Trim: 2000 Pontiac Bonneville SE
Re: Shallow aftermarket receiver?
I have the 2000 bonneville SE. What kind of tools do you use to cut it? I tried manipulating the right on cable and it seems to be like right on that plastic back there so I'm super nervous. But like I said I don't need a cd player and would prefer a touchscreen with a shallow depth so I don't have to cut anything
- bobgto65
- Posts like an L36

- Posts: 866
- Joined: Thu May 29, 2008 7:52 pm
- Year and Trim: 2002 SSEi
2004 Bonneville GXP - Location: Maryland
Re: Shallow aftermarket receiver?
just use a drill with a 1/2 inch bit and drill holes around the back next to each other until you cut out the whole back. A dremel tool may also work.
bobgto65

2004 Bonneville GXP 62,000 miles purchased 04/13
2009 G8 GXP PBM, M6 9580 miles, no mods, sold 08/15
2009 G8 GT SBM 36,000 miles, modded 430 whp
2002 Bonneville SSEi 203,200 miles (sold 3/2014)

2004 Bonneville GXP 62,000 miles purchased 04/13
2009 G8 GXP PBM, M6 9580 miles, no mods, sold 08/15
2009 G8 GT SBM 36,000 miles, modded 430 whp
2002 Bonneville SSEi 203,200 miles (sold 3/2014)
- repinS
- Moderator

- Posts: 7391
- Joined: Mon May 19, 2008 9:51 pm
- Year and Trim: 09 G8 GT
- Location: Toronto, Canada
- Contact:
Re: Shallow aftermarket receiver?
I used a hacksaw blade.

Jerry /// Past: 95 SSEi (June 2010 COTM) -- 04 GXP (July 2011 COTM)
91 Honda Civic Wagon DX 2WD (fuelly) -- 208,000km -- 92hp -- Autocross Warrior
09 Lexus LS460 AWD -- 94,000km -- Daily Driver
09 White Hot G8 GT -- 155,000km (fuelly) -- LS3 Cam -- GM LS3 CNC Ported Heads -- Kooks 1 3/4" Long Tube Headers -- Solo Catback Midsection -- Hooker Maxflow Mufflers -- Pat G Tune -- Rotofab Intake -- Tein S-Tech Springs -- GXP FE3 Dampers -- BMR Subframe Cradle Inserts -- BMR Subframe Connectors -- Forgestar F14 Gold 18x9 +40 -- Michelin Pilot Super Sport 245/45/18 -- Maverick Man Carbon Fiber Spoiler
- gweg_b
- Posts like a Northstar

- Posts: 1700
- Joined: Thu Dec 18, 2008 11:38 pm
- Year and Trim: 95 LeSabre Custom
01 Bonneville SSEi
09 G8 GT - Location: Cambridge, OH
- Contact:
Re: Shallow aftermarket receiver?
I had a friend help me. I removed the vent next to the radio and stuck my hand back there to hold the ribbon cable while he used a Dremel (yes, we were being careful with my hand, too). Took probably 5 minutes to complete.
I later went back in there with that Dremel to open up more space on the right side for hiding cables.
I later went back in there with that Dremel to open up more space on the right side for hiding cables.
- Greg | -- Project Prasinos -- |

1995 LeSabre Custom: 312K Miles | Custom K&N CAI | Edelbrock SDT Muffler | Camaro Tips | 180 T-stat | LED Interior
& Exterior | 20% Tint | PA Grill & Portholes | Limited Trim | GTP Rims | Ported LIM | Plus Many More Mods | Restoration Thread
2001 Bonneville SSEi: 225K Miles | Instense FWI | Intense MPS (3.4") | 180 T-stat | ZZP Plog | Ported Rear Manifold |
ZZP 3" Downpipe | Magnaflow Cat | Retrofitted HIDs | GenV M90 | GXP Brake Upgrade | 35% Tint | Plus Many More Mods |
2005 Bonneville GXP: 101K Miles | Custom FWI
2009 G8 GT: 89K Miles | 35% Tint | Roto-Fab CAI | SOLO Mach Exhaust | BMR Tunnel Brace | BMR Sub Frames | BMR STB |
Kooks Headers | QTP Electric Cutouts | BMR Sway Bars | Elite Engineering Catch Can | Innovative Dual Wideband Kit
1984 Caprice Classic Wagon: 86K Miles | Restoration Project

1995 LeSabre Custom: 312K Miles | Custom K&N CAI | Edelbrock SDT Muffler | Camaro Tips | 180 T-stat | LED Interior
& Exterior | 20% Tint | PA Grill & Portholes | Limited Trim | GTP Rims | Ported LIM | Plus Many More Mods | Restoration Thread
2001 Bonneville SSEi: 225K Miles | Instense FWI | Intense MPS (3.4") | 180 T-stat | ZZP Plog | Ported Rear Manifold |
ZZP 3" Downpipe | Magnaflow Cat | Retrofitted HIDs | GenV M90 | GXP Brake Upgrade | 35% Tint | Plus Many More Mods |
2005 Bonneville GXP: 101K Miles | Custom FWI
2009 G8 GT: 89K Miles | 35% Tint | Roto-Fab CAI | SOLO Mach Exhaust | BMR Tunnel Brace | BMR Sub Frames | BMR STB |
Kooks Headers | QTP Electric Cutouts | BMR Sway Bars | Elite Engineering Catch Can | Innovative Dual Wideband Kit
1984 Caprice Classic Wagon: 86K Miles | Restoration Project
-
IanRosean
- SLE Member

- Posts: 27
- Joined: Wed Feb 12, 2014 10:56 am
- Year and Trim: 2000 Pontiac Bonneville SE
Re: Shallow aftermarket receiver?
I purchased the gmrc 04 and I just ordered a mechless head unit that is only 3 and 5/8th inches deep so problem solved lol
Thanks for all the input though guys
Thanks for all the input though guys
-
DaMaroon
- SSEi Member

- Posts: 161
- Joined: Mon Oct 29, 2012 9:42 pm
- Year and Trim: 2003 SE
- Location: Darkest Ohio
Re: Shallow aftermarket receiver?
Did it have a screen/ touchscreen? If so what is it?
-
IanRosean
- SLE Member

- Posts: 27
- Joined: Wed Feb 12, 2014 10:56 am
- Year and Trim: 2000 Pontiac Bonneville SE
Re: Shallow aftermarket receiver?
No it didnt have a touchscreen it was a cheap Boss 614UA for $19 bucks on walmart.com, its all I need though because it pushes 50w to each speaker and i'm just gonna plug in my phone to it.
the only touchscreen I know of that will fit in our bonnies is the parrot asteroid which is like $499, im good on that hahaha
the only touchscreen I know of that will fit in our bonnies is the parrot asteroid which is like $499, im good on that hahaha

