Should I buy a high flow cat to replace it with? Or is that overkill?

Thanks for the info! Would this be picked up on an emissions test even if i was to clear it before hand? Also Is there a fix to this problem/does it have any effect on the car?

Thanks again
Mike

Hey guys thanks for the relpies. bought a code reader.. it has the capability of deleting, so i deleted earlier. after driving about 15 minutes it did come back though. Is this the o2 sensor on the intake?? Thanks in advance


p0140 sensor circuit no activity detected bank 1 sensor 2

Hey guys, was wondering if anyone could fill me in on what might be wrong here. My service engine soon light has been on for over a year now. The cars been running fine. Only modification ive done is FWI. May the air flow have anything to do with this? I have emissions test coming up, and I dont ...

One last question. On ebay it says this part is compatible on my car. Why would that be? I believe you 100% that the KYB SR1002 shocks are what I will need, but would there be any reason these wouldnt fit? I see they fit Cadillac with the same platform are listed. Shouldnt our cars be the same ...

You hit the nail right on the head when you said the back end will bounce around.. Thanks so much for the information. Now its just a matter of finding it at a local autozone or advanced. I found a pair for 130 at autozone but would have to have them shipped with a 3-5 day wait. Ebay seems to have ...

would prefer to buy a pair and change them both out if I could

Wow excellent write up! Instructions are great! Hopefully it doesnt snow tomorrow so I can do it then or at latest monday or tuesday. do you think it would be okay to drive on a few miles to work until then?

Also every time i search for rear shocks for my car on napa the same item keeps coming up ...

Hey all! I was hoping based on the picture below, someone could help me out to figure out what exactly i need. I believe the link below is what I need, but you guys surely know better than i do. I hope this is what I need. If there's something better or comparable, or if i need more than just this ...

would these work??

http://www.tunersdepot.com/Suspension/L ... -1359.html

Nos-thanks a ton for the help! Appreciate it!

Harofreak- How much are they?

Thanks

Yes my fathers monte carlo has the same problem but with his speedometer. My gauge has fallen below zero now.. to the point where it would normally sit when the car is off. Never moves. How much do these motors cost? and where can i find one?

Thanks a ton for the information.

Thanks for the response carl. It is frozen even when the car is off.. Just sits at 1k. Hope this helps!

Im sure the fact of where its stuck at rpms isnt an issue. But that fact that it IS stuck is. Not that its a problem to my car just more of a thing i would like to fix. What can my problem be?

Thanks any info is greatly appreciated.

Thanks!! Ended up getting it out!! It sounds amazing!! Cant wait to continue modding!!!

anyone have any pictures of what everything should look like step by step? the instructions they sent me arent helping me too much. For example, mounting the pcm tray, replacing the old sensor spot with new.. the sensor seems to be hard to get out of the old tubing. Any help would be great, ive done ...

Will the intake throw a code??

Hey all! One of the rods in my trunk snapped and need to figure out what the name is. I believe torsion rod or tension rod?? Anyways its the one that forces the trunk open because when i press the trunk button it just sits closed and i have to manually open it.. I know there is 2 bars that run ...

Anyone have any suggestions on diagnostic scanners to buy? Not looking for anything expensive, just to get the job done. Id like to spend around 100 or less if possible but if thats too cheap then id be willing to spend more.

Any input would be greatly appreciated.

A rod that goes across the length of my trunk snapped, causing it to not spring open when i press the button to open the trunk.. Never realized hoe heavy it was until this broke. Ill take a better look at where the rod comes from tomorrow. It looks like the welding on the right end broke at first ...