I just did my MC, i was driving down the the road and, they went to the floor had to use the e-brake. I didn't bench bleed it like they said i put it on then bleed it,its easyer that way. I didn't have to bleed the whole system either they work 100% better hope i helped

I recently did a trany swap, had some problems, but with the help of the people on this forum i(and my friend,BLAZZ) was able to fix it, ty again. Now iam back with another problem.

The car is still running good most of the time,
But now and then the voltage drops and the car runs like crap, Turn ...

The car is still runing good most of the time,
But now and then the voltage drops and the car runs like crap, Turn it off then back on it runs fine until the next time.... Its random..


We pulled the codes and, we got...

26,QDM "A" Circuit
56,QDM "B" Circuit

I haven't hooked up the TTC ground ...

The speed sensor was not pluged back in :angry7:

This caused the trany to shift into 2nd slow and a big loss in power at take off.

Car is runing better then ever now!! My buddy was used to haveing no power, when he tryed to pull it up the ramps he want up and over lol

After the work was done we ...

Yes it helped alot!! ty,

But it is for a 95 not 93, so i was told, ether way i needed both and it was a big help. ty

I did not look into the ratio yet, How would the car run/shift if it was not the same ratio?

i need to go back to the J/Y to get that code

here is the the pinout i found on your ...

it shift varry good better then the old trany did.

But when i tryed to drive it up the ramps to fix a started wire it would not make it up.

Other then that its working good. im going to do a trans filter ASAP i hope thats will help with geting it up the ramps.

NVM its shifting good

I need to get more gas into it, thats y its running SOOO... bad


TY again

IT WORKED :banana: :banana: :banana:


The engine is running really ruff but the tran is working,

it dont wont to go into 2nd in the small test drive i took Im hoping when i get the engine running right it will fix that.

Could i have wirded it up wrong to cause it not to shift?

even when it was ...

kk ty...

If this works im going to do back flips

Ok we tryed some spliceing with no luck, Im just going to wait for the 1993 schematic.

Also im going to try to post up a video of the car trying to move, its feels like there is not enough hydrulic prassure, the car moves but the plates slip,

I just want to make sure we are on the same page, What ...

Ya i was going to say..... I just looked at the car's pinout the wires are not all the same color.

This is what i got..

A. purple
B. Blue
C. red
D.tan
E.black
F.green
G. yellow

i meant trans filter
If i can find the 95 pinout i think i would be set

ty that will help,but i do need the 95 scematics also.tys alot i apreciate it. P.S. i didint change the oil filter yet! because i wanted 2 make sure the transmission worked before i put any $ in 2 it

Do you know what wires need to be swaped?

Or do you have the scimatics for both?

TY very much for the help so far

yes the bonne came with traction control but it dont work.<---never did

IDK if the 95 buick lesaber had traction control or not.

I hope thats it TY for the help



Can i re wire it from the plug side? there is planty of wire, does anyone know what wires would have to be spiced and switched?

ty

95 buick lesaber

Sorry its a 93 i posted in the wrong topic!!!


Also i forgot to say the car seem to go in reverse ok had to drive it back up the hill in reverse

I got a junk yard trany, the guy at the junk said the car sat for a long time the engine blew but the tranny was good,

I put it in.. and it slips in all gears the car will move but slips the whole time.

I was told it may be that the trany filter may be clogged from seting so long.

Is there any ...