I am bummed to say I never did this but this week for sure. I just got to my Camaro SS so that fuel was older. Can anyone tell me where is the relay on this car? And do I jump #30 and # 87 pins?

That's sounds good, can I remove the Schrader valve at the fuel rail and use a hose there? Can I leave the fuel relay in?. Big thanks for help guys.

I thought about that,a couple of tears ago I tested if the pump was working ,as it turned
out the tank was empty??
Can you explain stunting? And even jumping the pump?.Sorry to ask this much,I guess if I turned it over with starter it might damage something since the fuel would pump.out the fuel.

Hi folks it's been awhile since I was around. Hope all of you are doing Great. Curious I tried to stick a clear hose to siphon fuel that's about a year old. I slid it in close to 2 feet and tried to pump it out and nothing. The tube is dry like no gas??? Gauge says 1/2 tank I believe it's not ...

Hi folks its been awhile since i was here, hope all of you are healthy.What do i need to know about replacing my 1990 le balancer.Any hints? Thanks stay healthy.

Thanks Guys for the help, as it turned out the vacuum modulator on the trans was bad.... that thing was bad, eating atf like 8 ounces per 10 miles..And it had a white smoke from the tail pipe...This is mainly the problem from what a mechanic told me, if no leak under, or the coolant is green not ...

Hi folks I have a trans problem, my atf just gets low after a short drive over a few days...I checked underneath and no leaks on the driveway, also no signs of leakage underneath????? I was told it might leak into the radiator, its the original one from 1990..T coolant looks good, they said it ...

Today I installed a new flasher and they worked, however only the lever stays in position on a right turn, not the left??? Can there be another part I don't know of?? Thanks for the above help Sir.

Hi I have rplaced the switch twice over the years and it still doesn't work???? When you move the lever up it clicks but no blinking?? Also when you move the lever down it wont click, or blink ata all.The arrow will go green but that's it.PLEAS HELP, I have replaced switches on other cars with no ...

Check engine light came on intermittently actually just once.I pulled a code 42 this seems kind of hard to figure out.Today while the car was idling in park the motor increased in rpms and backed down after maybe 3 seconds?? My auto seems to kinda have a tuff time to turn over, 2 year old delsco ...

Guys it was a crimped wire from a bend.I used a voltmeter and when I got to the bend it dropped voltage?? CRAZY but it works now after straightening the wire out,kinda strange to me.Thanks for the input.

Hi I have a bulb on the license plate light that does not work I did replace the old one that was bad about six months ago.Now I see it doesn't work, and the voltage drop is about 1 volt or a little more.Does anyone know what that means?? I have some electric exp but this problem is NEW to me,thanks.

Sorry but have been busy painting the car,the oil leak is gone YESSSS .Thanks for the help guys

Hi any tips for this job, and is it difficult?? Should I use delco or felpro gaskets.Thanks in advance

I have the same problem but if I buy a new cable will it stay on better??? Not sure if something on the end of the cable is worn out or missing,broke?? Does anyone know how it should look?

Last year I replaced my pcv valve after I had removed the intake for gaskets.I would recommend spraying some typs of lube like wd40 and slowly wiggle the thing out.Mine broke and the bottom half of the grommet went into the intake manifold. It takes 2 grometts so be very careful they get brittle ...

Thanks Yea I replaced the pressure line and it still leaked.Also under the pump and reservoir its kinda oily, gotta be the seals? What is the best way to spot the leak, I checked while the car is running and cant see anything, its kinda starnge with the belt and stuff spinning, worried about losing ...

What kind of tools are needed to remove and install the pulley on the power steering pump? Also has anyone replaced the O-rings and seals on a pump? Mine just leaks but it works fine. Thanks in advance guys.

GREAT pic and advice, the nut underneath is where you can put a wrench on it.Thanks again, you are clearly a awesome person and glad too hear your words of wisdom i owe you a beer.

Just wanted to say on my 1990 model i found fuses and relays behind the glove box. Open the box up and pull the tabs in the back and then there are a few 7mm i think screws under the box and remove them and then you have perfect access tp the panel.Thats where my fuel pump relay was,NOT under the ...